MAIN CHARACTERISTICS
range of product
ALTIVAR 71
product or component type
VARIABLE SPEED DRIVE
product specific application
COMPLEX HIGH-POWER MACHINES
component name
ATV71
motor power kW
200 KW AT 500 V 3 PHASES
motor power hp
250 HP AT 575 V 3 PHASES
motor cable length
NO RENDITION
power supply voltage
500...690 V (- 15...10 %)
network number of phases
3 PHASES
line current
249 A FOR 600 V 3 PHASES 300 HP
EMC filter
INTEGRATED
assembly style
WITH HEATSINK
variant
REINFORCED VERSION
prospective line Isc
<= 35 KA 3 PHASES
nominal output current
242 A AT 2.5 KHZ 575 V 3 PHASES 300 HP
maximum transient current
468 A FOR 60 S 3 PHASES 200 KW
output frequency
0.1...500 HZ
nominal switching frequency
2.5 KHZ
switching frequency
2.5..4.9 KHZ ADJUSTABLE
asynchronous motor control profile
ENA SYSTEM F UNBALANCED LOADS
type of polarization
NO IMPEDANCE FOR MODBUS
COMPLEMETARY CHARACTERISTICS
product destination
ASYNCHRONOUS MOTORS
power supply voltage limits
425...759 V
power supply frequency
50..60 HZ - 5..5
power supply frequency limits
47.5..63 HZ
speed range
1...100 FOR ASYNCHRONOUS MOTOR IN OPEN-LOOP MODE WITHOUT SPEED FEEDBACK
speed accuracy
+- 0.01 OF NOMINAL SPEED FOR 0.2 TN TO TN TORQUE VARIATION IN CLOSED-LOOP MODE WITH ENCODER FEEDBACK
torque accuracy
+- 15 IN OPEN-LOOP MODE WITHOUT SPEED FEEDBACK
transient overtorque
170 OF NOMINAL MOTOR TORQUE +- 10 FOR 60 S EVERY 10 MINUTES
braking torque
<= 150 WITH BRAKING OR HOIST RESISTOR
synchronous motor control profile
VEC CTRL W O SPEED FEEDBACK
regulation loop
ADJUSTABLE PI REGULATOR
motor slip compensation
ADJUSTABLE
diagnostic
1 LED RED PRESENCE OF DRIVE VOLTAGE
output voltage
<= POWER SUPPLY VOLTAGE
insulation
ELEC BTWN POWER AND CONTROL
type of cable for mounting in an enclosure
with a NEMA Type1 kit : 3-strand UL 508 cable at 40 °C, copper 75 °C PVC
electrical connection
AI1-AI1+ AI2 AO1 R1A R1B R1C R2A R2B LI1...LI6 PWR TERMINAL 2.5 MM AWG 14
tightening torque
AI1-AI1+ AI2 AO1 R1A R1B R1C R2A R2B LI1...LI6 PWR 0.6 N.M
supply
INTERNAL SUPPLY FOR REFERENCE POTENTIOMETER 1 TO 10 KOHM 10.5 V DC +- 5 <= 10 MA FOR OVERLOAD AND SHORT-CIRCUIT PROTECTION
analogue input number
2
analogue input type
AI1-AL1+ BIPOLAR DIFFERENTIAL VOLTAGE +- 10 V DC INPUT VOLTAGE 24 V MAX RESOLUTION 11 BITS + SIGN
input sampling time
AI1-AL1+ 2 MS +- 0.5 MS FOR ANALOG INPUTS
response time
<= 100 MS IN STO SAFE TORQUE OFF
absolute accuracy precision
AI1-AL1+ +- 0.6 FOR A TEMPERATURE VARIATION 60 C
linearity error
AI1-AL1+ AI2 +- 0.15 OF MAXIMUM VALUE
analogue output number
1
analogue output type
AO1 SOFTWARE-CONFIGURABLE LOGIC OUTPUT 10 V <= 20 MA
discrete output number
2
discrete output type
R1A R1B R1C CONFIGURABLE RELAY LOGIC NONC ELECTRICAL DURABILITY 100000 CYCLES
minimum switching current
CONFIGURABLE RELAY LOGIC 3 MA AT 24 V DC
maximum switching current
R1 R2 ON INDUCTIVE LOAD 2 A AT 250 V AC COS PHI = 0.4
discrete input number
7
discrete input type
LI1...LI5 : programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm
discrete input logic
LI1...LI5 NEGATIVE LOGIC SINK > 16 V STATE 0 < 10 V STATE 0
acceleration and deceleration ramps
AUTO ADPT OF RAMP IF BKG EXD
braking to standstill
BY DC INJECTION
protection type
DRIVE AGAINST EXCEEDING LIMIT SPEED
insulation resistance
> 1 MOHM AT 500 V DC FOR 1 MINUTE TO EARTH
frequency resolution
ANALOG INPUT 0.02450 HZ
communication port protocol
CANOPEN
connector type
1 RJ45 FOR MODBUS ON FRONT FACE
physical interface
2-WIRE RS 485 FOR MODBUS
transmission frame
RTU FOR MODBUS
transmission rate
4800 BPS 9600 BPS 19200 BPS 38.4 KBPS FOR MODBUS ON TERMINAL
data format
8 BITS 1 STOP EVEN PARITY FOR MODBUS ON FRONT FACE
number of addresses
1..127 FOR CANOPEN
method of access
SLAVE FOR CANOPEN
marking
CE
operating position
VERTICAL + -10 DEGREE
height
1190 MM
depth
377 MM
width
595 MM
product weight
207 KG
option card
CC-LINK COMMUNICATION CARD
ATV71HC25Y - variable speed drive ATV71 - 250kW - 690V - EMC filter-graphic terminal, Schneider Electric
- Product Code: ATV71HC25Y
- Brand: Schneider Electric
- Availability: To be confirmed
- € 34,216.05 Ex Tax:
