MAIN CHARACTERISTICS
range of product
ALTIVAR LIFT
product or component type
VARIABLE SPEED DRIVE
device short name
ATV71
product destination
ASYNCHRONOUS MOTORS
product specific application
LIFT
assembly style
WITH HEATSINK
variant
W INTD 7-SEGMENT DISPLAY TERM
EMC filter
INTEGRATED
network number of phases
3 PHASES
[Us] rated supply voltage
380...480 V (- 15...10 %)
supply voltage limits
323...528 V
supply frequency
50..60 HZ - 5..5
network frequency
47.5..63 HZ
motor power kW
3 phases
motor power hp
3 phases
line current
14.1 A FOR 380 V 3 PHASES 4 KW 5 HP
COMPLEMETARY CHARACTERISTICS
apparent power
9.3 KVA FOR 380 V 3 PHASES 4 KW 5 HP
prospective line Isc
<= 5 KA 3 PHASES
nominal output current
10.5 A AT 4 KHZ 380 V 3 PHASES 4 KW 5 HP
maximum transient current
14.3 A FOR 2 S 3 PHASES 4 KW 5 HP
speed drive output frequency
0...599 HZ
braking resistance
>= 19 OHM
nominal switching frequency
8 KHZ
switching frequency
1..16 KHZ ADJUSTABLE
speed range
1...100 ASYNCHRONOUS MOTOR IN OPEN-LOOP MODE WITHOUT SPEED FEEDBACK
speed accuracy
+- 0.01 OF NOMINAL SPEED FOR 0.2 TN TO TN TORQUE VARIATION IN CLOSED-LOOP MODE WITH ENCODER FEEDBACK
torque accuracy
+- 5 IN CLOSED-LOOP MODE WITH ENCODER FEEDBACK
transient overtorque
170 +- 10 FOR 60 S
braking torque
30 WITHOUT BRAKING RESISTOR
asynchronous motor control profile
VOLTAGE FREQUENCY RATIO 2 PTS
synchronous motor control profile
VECTOR CONTROL W O SENSOR STD
regulation loop
ADJUSTABLE PI REGULATOR
motor slip compensation
ADJUSTABLE
local signalling
1 LED - RED - DRIVE VOLTAGE
output voltage
<= POWER SUPPLY VOLTAGE
insulation
ELEC BTWN POWER AND CONTROL
type of cable for external connection
IEC cable without mounting kit : 1 wire(s) - 45 °C, copper 90 °C / XLPE/EPR
electrical connection
TERMINAL 2.5 MM AWG 14 AI1-AI1+ AI2 AO1 R1A R1B R1C R2A R2B LI1...LI6 PWR
tightening torque
1.4 N.M - 12.3 LB.IN L1R L2S L3T UT1 VT2 WT3 PC- PO PA+ PA PB
supply
internal supply for reference potentiometer (1 to 10 kOhm) at 10.5 V DC +/- 5 % - <= 10 A with overload and short-circuit protection
analogue input number
2
analogue input type
software-configurable voltage : (AI2) 0...10 V DC - 24 V max - 30000 Ohm - resolution: 11 bits
sampling duration
2 ms +/- 0.5 ms (LI6) if configured as logic input - discrete input(s)
response time
7 MS +- 0.5 MS R1A R1B R1C - DISCRETE OUTPUTS
accuracy
+- 0.6 AI1-AL1+ FOR A TEMPERATURE VARIATION 60 C
linearity error
+- 0.15 OF MAXIMUM VALUE AI1-AL1+ AI2
analogue output number
1
analogue output type
software-configurable voltage : (AO1) 0...10 V DC - 470 Ohm - resolution: 10 bits
discrete output number
2
discrete output type
configurable relay logic : (R1A, R1B, R1C) NO/NC - 100000 cycles
minimum switching current
3 MA AT 24 V DC CONFIGURABLE RELAY LOGIC
maximum switching current
5 A AT 250 V AC ON RESISTIVE LOAD - COS PHI = 1 - LR = 0 MS R1 R2
discrete input number
7
discrete input type
PROGRAMMABLE LI1...LI5 24 V DC WITH LEVEL 1 PLC - 3500 OHM
discrete input logic
positive logic (LI6) if configured as logic input, < 5 V (state 0), > 11 V (state 1)
acceleration and deceleration ramps
AUTO ADPT OF RAMP IF BKG EXD
protection type
OVERHEATING PROTECTION FOR DRIVE
dielectric strength
3535 V DC BETWEEN EARTH AND POWER TERMINALS
insulation resistance
> 1 MOHM AT 500 V DC FOR 1 MINUTE TO EARTH
frequency resolution
0.1 HZ FOR DISPLAY UNIT
communication port protocol
CANOPEN
connector type
1 RJ45 FOR MODBUS ON FRONT FACE
physical interface
2-WIRE RS 485 FOR MODBUS
transmission frame
RTU FOR MODBUS
transmission rate
9600 BPS 19200 BPS FOR MODBUS ON FRONT FACE
data format
8 BITS 1 STOP EVEN PARITY FOR MODBUS ON FRONT FACE
type of polarization
NO IMPEDANCE FOR MODBUS
number of addresses
1..247 ADDRESSES FOR MODBUS
method of access
SLAVE FOR CANOPEN
control options
COMMUNICATION CARD FOR MODBUS TCP
operating position
VERTICAL + -10 DEGREE
ATV71LD10N4Z - variable speed drive ATVLift - 4 kW 5 Hp - 480 V - EMC filter - with heat sink, Schneider Electric
- Product Code: ATV71LD10N4Z
- Brand: Schneider Electric
- Availability: To be confirmed
- € 910.25 Ex Tax:
